MENU
News
  1. Home
  2. /
  3. Boiler Steels
  4. /
  5. low temperature carbon steel plate s45c

low temperature carbon steel plate s45c

S45C Carbon Steel| 760 |CK45: Carbon Steel Supplier MalaysiaS45C Carbon Steel also known as AISI 1045 Steel is a medium tensile low hardenability carbon steel generally supplied in the cold drawn or turned and polished condition, with a typical tensile strength range 600 – 950 Mpa and Brinell hardness range 179 – 280. in either condition.

Get A Price [email protected]
  • 1045 S45C C45 Steel Properties Heat Treatment

    Such as gears, shafts, piston pins, and etc. 1045 Steel properties and heat treat as below. C45 Steel Characteristics. It is carbon steel and has great weldability and machinability. After normalized and hot rolled, it will get high strength and impact properties. It has low hardenability and critical hardenability diameter is 12 17mm in the water.

  • Low Temperature Carbon Steel Plate S45c Din 1.2312,4140,1

    Low Temperature Carbon Steel Plate S45c Din 1.2312,4140,1.2379,718,1045 Steel,Aisi 4140 Steel , Find Complete Details about Low Temperature Carbon Steel Plate S45c Din 1.2312,4140,1.2379,718,1045 Steel,Aisi 4140 Steel,4140 Carbon Steel Plate,Aisi 4140 Steel,Steel Plate 4140 from Steel Pipes Supplier or Manufacturer Beijing Topensea International Trade

  • Minimum temperature range for common low carbon steels

    Oct 07, 2004 · For plates only, a specification like ASTM A 516 "Pressure Vessel Plates, Carbon Steel, for moderate and lower temperature Service". Order with supplementary requirement S5 Charpy impact test. ASTM A 573 "Structural Carbon Steel Plates of Improved Toughness". These steels are made to a fine grain practice.

  • Q&A What is the difference between LTCS and Carbon steel

    Nov 07, 2011 · Low Temperature Carbon Steel Tubes ASTM A334 Gr.1 *ASTM A420 For LTCS Fittings. *A350 LF2 is a standard For Flanges. · Steels with carbon contents greater then 0.25% · All forging grades of steel. · Structural steels with carbon content between 0.15 to 0.25%. · Some special steel in the lower carbon ranges.

  • Low Temperature Carbon Steel Plate S45c Din

    low temperature carbon steel plate S45C DIN 1.2312, 4140, 1.2379, 718, 1045 steel,aisi 4140 steel

  • Low Temperature Carbon Steel Plates Find Manufacturer

    Low Temperature Carbon Steel is the term used to denote any steel that is non stainless steel type. To include a steel in carbon steel category, it has to have 2.1% carbon of its total weight. It should contain molybdenum, nickel, niobium, titanium, tungsten and zirconium in unspecified quantities.

  • Low Temperature Carbon Steel Plate Products &

    DescriptionWith an extremely low coefficient of thermal expansion, approximately one tenth that of carbon steel at temperatures up to 400° F, Invar® is often thought of as the material of choice for low expansion nickel alloy applications. The ability to maintain strength at

  • A516 Steel Plate Grade 55, 60, 65, 70 Leeco Steel, LLC

    ASTM A516 is a PVQ carbon steel plate intended primarily for service in welded pressure vessels at moderate or lower temperatures, where notch toughness is important. OverviewAvailable in four grades55, 60, 65 and 70.

  • Carbon Steel Plates McMaster Carr

    Stronger than low carbon steel with equally good machinability, 1045 carbon steel is widely used for bolts, studs, and shafts. Wear Resistant AR400 Carbon Steel The nickel and molybdenum content gives AR400 carbon steel the ability to resist wear better than all other carbon steel.

  • Carbon Steel Low Temperature Bend, Buttweld Fittings

    Kalikund Steel is one of the Manufacturer & Exporter of Carbon Steel Low Temperature Bend, Low Temperature Buttweld Fittings, Low Temperature Forged Fittings, Low Temperature Outlets, Low Temperature Flanges, Low Temperature Pipe, Low Temperature Plate, Low Temperature Bar.

  • Carbon Steel Plate Qingdao Hengjia Steel Pipe Co., Ltd

    China Carbon Steel Plate catalog of S45c ASTM A283 Grc A36 1045 Hot Rolled Steel Plate, ASTM 1045 S45c St52 S355jr Low Alloy Steel Plate provided by China manufacturer Qingdao Hengjia Steel Pipe , page1.

  • AISI 1045 Carbon Steel CK45 JIS S45C Sheet plate Forged

    AISI 1045 Carbon Steel G10450 \ Din CK45 W Nr. 1.1191 JIS S45C Sheet Plate. This steel shows reasonable strength and toughness. AISI 1045 will through harden to 2.5” (63mm) with a tensile strength of 66 120 Ksi (620 850 MPa) .

  • Microstructure and mechanical properties of S45C steel

    In this study, commercial carbon steel S45C plates with a thickness of 3.2 mm were subjected to the FSW process. The S45C steel has a ferrite plus pearlite structure and its chemical composition is listed in Table 1.For the welding process, the steel plates were first placed on a steel back plate made of SUS304 and clamped tightly.

  • Carbon Steel Plates for Pressure Vessels for Low

    JFS Steel Carbon Steel Plates for Pressure Vessels for Low Temperature Service Introduction. Professional Steel Supplier & Service Integration.. Ju Feng was originally founded as a construction company for 47 years ago and also successfully expanded into the Special Steel Industry which a leading supplier of special steel material (bar, plate, tubeetc.) in Taiwan since 2006. precision

  • Carbon Steel Low Temperature Bend, Buttweld Fittings

    MaterialsLow Temperature carbon Steel Plate – LTCS Plate, ASTM A516 Gr. 70 LTCS Bar Range5 mm To 500 mm thick in 100 mm TO 6000 mm Length available with NACE MR 01 75.

  • What is the difference between LTCS and Carbon steel

    Apr 14, 2009 · *LTCS is a Nickel based alloy steel plates especially used for low temperature applications below 150 deg F. Mainly used in cryogenic construction of space ships, low temperature application in chemical plant below 55 deg C. ExamplesSA 203 Steel Plate Grades A, B, D, E and F Nickle Alloy Steel Plates. For low temperatures ( 150 deg F)

  • Steel Plate Grades Continental Steel & Tube Company

    low carbon plate steel Low Carbon Plate Steel is manufactured to three separate carbon ranges that relate to thickness and end use requirements. Plates 3/4″ and lighter are produced to the lowest carbon range (0.10 0.20) for maximum cold forming and welding properties.

Our Steel Products' Certificates:

Steels Certificates

Our Factory:

Steels factory

Packaging & shipping:

Packaging & Shipping

What Can I Do For you?