MENU
News
  1. Home
  2. /
  3. Steel Grades
  4. /
  5. high strength degree carbon steel plate

high strength degree carbon steel plate

Carbon & High Strength Low Alloy (HSLA) Structural Steel Carbon &160;High Strength Low Alloy (HSLA) Structural Steel Plate Leeco 174; Steel carries a deep inventory of carbon or mild steel plate as well as High Strength Low Alloy or HSLA steel plate. HSLA boasts a higher strength, lower weight and good machinability and ductility compared to conventional mild carbon steel grades.

Get A Price [email protected]
  • Offshore High Strength North Shore Steel North Shore Steel

    High strength carbon steel plate, primarily used for shipbuilding and other marine equipment. Normally included ABS certification. Produced in as rolled and normalized conditions up to 6”.

  • Carbon Steel an overview ScienceDirect Topics

    Carbon steel is produced as ingots, or flat plate or sheet. Until the 1960s carbon steels were produced with strengths up to X 52 (where X indicates the yield strength of carbon steel; X 52 means the yield strength of the carbon steel is 52,000 psi) (see section 3.4.2 for specification) and were delivered in the as rolled or normalized condition. The process of controlled rolling was discovered in the early 1960s

  • HIGH STRENGTH High Strength and Abrasion Resistant

    High Strength Plates & Profiles Inc. is a global leader in the processing of high strength and abrasion resistant steel. We offer one stop shopping for high strength and abrasion resistant steel from full plates to finished parts. Founded in 1985, we have over 5000 tons of

  • Plate

    The plates are available in three grades having different strength levels. ASTM – A515 – Standard specification for pressure vessel plates, carbon steel, for intermediate and higher temperature service. This specification covers carbon silicon steel plates primarily for intermediate and higher temperature service in welded boilers and other pressure vessels. The plates are available in three grades each having different strength levels.

  • High Strength Low Alloy Steel an overview

    Jan 01, 1993 · In the modern automotive industry, the tensile strength of mild steel and high strength low alloy steel is from 300 to 450 MPa. Due to the increasing demand of weight reduction, the tensile strength of parts manufactured by IHPF will increase to 500–600 MPa, and even to 1000 MPa.

  • ASTM A572 Grade50,55,60 HSLA Structural Steel Plate AGICO

    ASTM A572 Carbon Steel Plate. ASTM A572 Specification refers to High Strength Low Alloy Steel Plate for structural building, among the 5 steel grades of 42, 50, 55, 60 and 65, Grade 50 is one most common steel in applications where need more strength and less weight, use steel plate of this grade other than ordinary carbon steel will make the steel structure with same steel strength but

  • Plate Grades Steel Plate Akron Steel Plate Atlanta

    ASTM A709 50W covers high strength, low allow steel structural shapes, plates and bars. The atmospheric corrosion resistance of this steel in most environments is substantially better than carbon steel with or without copper addition. ASTM A709 50W shall have an

  • Carbon Steel, High Strength Low Alloy, Stainless Steel

    ASTM A588 is a High Strength Low Alloy Steel that is used in general structural applications when the structural will be riveted, bolted, or welded. ASTM A588 is a Copper bearing steel that offers a minimum yield of 50 KSI and has approximately two to four times the corrosion resistance of

  • Classification of Carbon and Low Alloy Steels

    The carbon content for these high formability steels is very low, less than 0.10% C, with up to 0.4% Mn. Typical uses are in automobile body panels, tin plate, and wire products. For rolled steel structural plates and sections, the carbon content may be increased to approximately 0.30%, with higher manganese content up to 1.5%.

  • Mirraloy® FM TGP 1144 Steel Associated Steel Corporation

    High Strength Steels Mirraloy® FM TGP 1144 (modified) Free Machining, Turned Ground & Polished, Carbon Shaft. Mirraloy FM is a modified 1144 steel. Typical hardness is Rockwell “C” 26. Mirraloy FM is a high strength micro alloyed, free machining carbon steel. Typical tensile strength 133,000 PSI.

  • Steel Plates & Sheets Hillside, New Jersey Arco Steel

    ASTM A36 is a Carbon Steel that is used in general plate applications when the plate will be riveted, bolted, or welded. ASTM A36 is produced to chemical and mechanical properties that offer a minimum yield of 36 KSI and a tensile range of 58 KSI to 80 KSI on plates up to 8 inches thick. ASTM A572 GR 50 is a High Strength Low Alloy Steel that is used in general plate applications when the plate will be

  • Plate Grades Steel Plate Akron Steel Plate Atlanta

    A709 50. SpecificationsASTM A 709 50 WorkabilityASTM A709 50W is a standard specification for structural steel in bridges. ASTM A709 50W covers high strength, low allow steel structural shapes, plates and bars. The atmospheric corrosion resistance of this steel in most environments is substantially better than carbon steel with or without copper addition.

  • Welding of High Strength Bolts to Carbon Steel Plates

    Feb 24, 2010 · A325 Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength. That being read you would have to develop a procedure and have it approved by the EOR. I have seen Engineers allow tacking nuts to plates in a blind splice connection for a

  • C1020 Steel Plate ASTM A830 C1020 Steel Plate Leeco

    Leeco ® Steel carries a robust supply ASTM A830 1020 steel plate. Request a quote online or contact a sales representative today to place an order. Request a quote online or contact a sales representative today to place an order.

  • Delta Steel, Inc. Plate

    A high strength low alloy steel plate used in a variety of structural applications. It is produced in grades 42, 50, 60, 65 representing the yield strength. Mechanical PropertiesA 572 GR 42. Tensile60 KSI minimum; Yield42 KSI minimum; Elongation18% minimum in 8” 22% minimum in 2” (for plate 24” and wider) Mechanical PropertiesA 572 GR 50

  • Carbon Steel Plate Royal Metal Industries

    A514 is a specific high strength steel, which is quenched and tempered alloy steel, with a yield strength of 100k psi. A588 = Is a high strength low alloy structural steel, with improved corrosion resistance for structural steel shapes such as angles, channel and beams, as well as steel plate and bars.

  • HIGH STRENGTH High Strength and Abrasion Resistant Steel

    High Strength Plates & Profiles Inc. is a global leader in the processing of high strength and abrasion resistant steel. We offer one stop shopping for high strength and abrasion resistant steel from full plates to finished parts. Founded in 1985, we have over 5000 tons of

Our Steel Products' Certificates:

Steels Certificates

Our Factory:

Steels factory

Packaging & shipping:

Packaging & Shipping

What Can I Do For you?